Why the Gage Bilt GB947 Is the Power Unit I Recommend for Serious Lockbolt Work
Every fastening
crew I talk to says some version of the same thing: the tool in your hand gets
the credit, but the power behind it decides whether the job goes smoothly. A
hydraulic installation tool can only be as consistent as the unit feeding it.
So when someone asks me what belongs at the heart of a lockbolt setup, my
answer keeps landing on one machine: the Gage Bilt GB947 hydraulic
power unit.
In this post,
I'll walk you through what the GB947 is, what it does well, who gets the most
out of it, and what to confirm before you order. If you finish reading and
still have questions, I'm one phone call away.
What the GB947 Actually Is
The GB947 is a
portable, electrically operated hydraulic power source designed to run Gage
Bilt hydraulic installation equipment. It is also compatible with Huck®
hydraulic installation equipment, which matters if your shop owns tooling from
more than one lineage and you'd rather not maintain separate power sources.
It comes in two
voltage versions. The standard GB947 runs on 115-volt, 50/60 hertz,
single-phase power, and I'd plan on a 20-amp circuit for it. The GB947-220 runs
on 230-volt, 50/60 hertz, single-phase power. Pick the version that matches the
outlets in your shop or hangar, and you're set.
Power Where It Counts
Inside, a 1-1/2
hp electric motor drives a two-stage, gear-piston hydraulic pump that delivers
roughly 75 cubic inches per minute at 5,000 psi. Output pressure is adjustable
up to 10,000 psi, but the unit ships with settings tuned for installation work:
the pull side is set at 5,400–5,700 psi and the return side at 2,200–2,400 psi.
What I like
most is how the cycle manages itself. A four-way directional valve sends fluid
to either the PULL or RETURN port on your tool, and it's controlled by a
24-volt system built into the installation equipment. That means the operator
runs the cycle from the tool instead of walking back to the unit. An external
relief valve controls pull pressure, while a pressure switch watches return
pressure and shuts the unit off automatically once the actuator is released and
the installation cycle is finished. A factory-preset internal relief valve adds
protection for both the equipment and the person holding it.
For a
technician installing fasteners all day, that adds up to fewer variables and
fewer things to babysit.
Portable Enough to Follow the Work
At 52 lbs dry
and about 62 lbs with oil, and a footprint of roughly 17.9" high,
10.5" wide, and 13.9" long, the GB947 is a unit one person can
reposition without calling for a forklift. The reservoir holds approximately
2.5 gallons and runs on DEXRON® III or equivalent ATF, a fluid you can find
almost anywhere, so top-offs never turn into a scavenger hunt.
It's rated for
ambient temperatures from -20°F to 122°F, so a freezing morning in the yard and
a sweltering afternoon in the hangar are both on the table. One honest note: it
runs at around 90 dB(A), so hearing protection belongs in the plan from day one.
Where I See It Earning Its Keep
If your work is
heavy-duty repair, the GB947 gives you a dependable source of hydraulic
pressure that travels from bay to bay or from the shop to the trailer. Crews in
that world should look at our trucking nose selection, which pairs naturally with a power
unit built for this kind of duty.
If you maintain
aircraft, consistency is not a nice-to-have, it's the entire job. Our aviation nose collection is where I'd send you to match your
installation tooling to the work in front of you, with the GB947 supplying
steady pull and return pressure behind it.
And if you're
running a fabrication shop that touches both worlds, one portable unit that
serves Gage Bilt and Huck®-compatible equipment simplifies your floor plan and
your purchasing.
Build the Whole System, Not Just One Piece
A power unit is
the foundation, but it works best with the right partners. Start with our Gage Bilt collection for new hydraulic installation tools.
Move on to the Gage
Bilt noses to get the
jaws that fit your fasteners, and check the accessories and parts page for the supporting items you'll
want on the shelf before you need them.
If you'd rather
stage your investment in steps, our refurbished
Huck® brand tools let you add
installation capacity without buying everything new at once.
The Math Behind an $8,716 Investment
The GB947 is
listed at $8,716, and I won't pretend that's an impulse buy. It's a capital
purchase, and it deserves to be judged like one. A unit with factory-set pull
and return pressures, automatic shutoff, and a design made to run Gage Bilt and
Huck®-compatible equipment is built to take variability out of the process.
When I weigh that against the cost of rework, rejected installs, or a crew
standing around waiting for a borrowed power source, the conversation usually
shifts from price to value.
The question
I'd encourage you to ask isn't "What does it cost?" but "What
does it cost me when my power source isn't consistent?"
Buying with Confidence
You can check
out with Visa, Mastercard, American Express, Discover, Diners Club, or Shop
Pay, and your payment information is processed securely. Unused items in their
original packaging can be returned within 30 days, and I'd encourage you to
read our returns
policy before
ordering so there are no surprises, including how return shipping is handled.
Before You Order, Tell Me Three Things
I can usually
confirm whether the GB947 is the right match quickly if you send me:
- Your available voltage. 115-volt or 230-volt decides
which version you need.
- Your tooling. Tell me the Gage Bilt or Huck®
models you plan to run so I can check the pairing.
- Your application. Trucking, aviation, or general
fabrication, so I can point you toward the right noses and accessories.
Then reach out
whichever way suits you. Call me at 360-923-1012 or email sales@reliableairtools.com, and I'll get you a straight
answer. If you'd like to keep learning before you buy, our blog is full of practical
fastening insight, and you can always start fresh at Reliable Air Tools.
The right power
unit won't make headlines, but it will quietly make every install on your
schedule more predictable. That's exactly why I keep recommending the GB947.

Comments
Post a Comment